Blogs /
Concrete Pump Pipe Warranty: What Evidence You Need Before You Claim

Concrete Pump Pipe Warranty: What Evidence You Need Before You Claim

**Pump Pipe Wear Guarantee** A pump pipe that fails early is only a claim if you can prove it. What a wear guarantee has to state in cubic metres, why goods-in wall thickness measurement decides the outcome, the evidence pack a manufacturer can actually process, and how a pro-rata credit is calculated.

News Details

A delivery pipe that fails after four months is an argument. A delivery pipe that fails after four months, on a line whose wall thickness was measured on arrival, the pumping volume was logged, and the failure was photographed with a calliper in frame, is a claim.

The difference is almost never the supplier's goodwill. It is documentation. Wear parts occupy an awkward position in a purchase contract: they are designed to wear out, so failure at the end of their life is correct behaviour, and the only question a manufacturer can answer is whether the end came sooner than the agreed life. Everything that follows depends on whether you can state, with evidence, what "sooner" means.

Two different promises, often confused

Most pump pipe disputes start because the buyer and seller each believe a different warranty applies.

A calendar warranty covers defects in material and workmanship for a stated period after delivery. It is about whether the pipe was made correctly. It does not promise that the pipe will last a given number of months on site, because service intensity varies by an order of magnitude between a tower project and a ready-mix depot.

A wear guarantee is expressed in conveyed volume, usually cubic metres of concrete. It promises that the pipe will convey a stated volume before reaching its retirement wall thickness or leaking, under defined conditions. This is the number buyers actually care about, and it is also the one that is hardest to prove after the fact.

Both can apply to the same order. They answer different questions, they have different claim windows, and they need different evidence. A purchase order that says only "warranty: one year" has answered neither.

What a wear guarantee has to define

A conveyed-volume figure without conditions is a marketing number. To be usable in a claim, it needs the following stated in writing.

Element Why a claim depends on it
Reference conditions Aggregate type and size, slump, pump pressure, pipe position in the line. Crushed granite at high pressure wears a pipe several times faster than rounded river gravel at low pressure. Position in the line The section immediately after the hopper and the first vertical riser sections wear far faster than the horizontal tail. A single guarantee figure across all positions is not meaningful. Starting wall thickness Measured, not nominal. Without a starting value there is no wear rate to calculate. End-of-life definition Usually a percentage of wall loss or a leak at the weld. A vague "worn out" cannot be tested. Measurement method Ultrasonic thickness gauge, points per pipe, and whether the thinnest reading or an average governs Exclusions Mechanical damage, over-pressure, dry running, blocked line and restarted pump, incorrect clamp torque, mixed-brand assemblies Remedy and calculation Replacement, pro-rata credit, or credit against the next order, and the formula for each

Manufacturers who publish design life figures for their products normally publish them against a stated construction: for example, a single-layer quenched pipe rated for a given volume at a stated hardness range. The quenched wear-resistant pipe specification sets out design life against wall structure and hardness. When you write a guarantee into a PO, anchor it to the published figure for the exact variant you are buying, not to the best figure in the range.

The baseline problem

Almost every failed wear claim fails here. The buyer has a pipe that wore through in 18,000 m³ against a 40,000 m³ guarantee. The supplier asks what the wall thickness was at delivery, and the answer is the nominal figure from the catalogue.

Nominal wall thickness is not a measurement of your pipe. Wall thickness varies within tolerance along a length, and the thinnest point governs life. Two practices close the gap, and both take minutes at goods-in.

  • Measure wall thickness with an ultrasonic gauge at both ends of every pipe, at four points around the circumference, and record the minimum.
  • Record the heat number and match it to the mill certificate. Where a shipment contains more than one heat, keep the pipes grouped by heat so a later failure can be traced to a batch.

The guide to verifying concrete pump parts sets out the incoming inspection routine in more detail, including hardness checks and document review. The goods-in sheet it produces is the same sheet you will attach to a claim two years later.

The evidence pack

A claim that a manufacturer can process without argument contains the following. Assemble it as a single file, indexed, not as a chain of photographs in a chat app.

Document What it proves
Purchase order and invoice Which specification was contracted, including any guarantee figure written into the PO
Packing list with heat numbers Which physical pipes correspond to which batch
Mill certificate / material test report Steel grade actually supplied
Hardness report Whether the inner wall met the specified range
Goods-in thickness sheet with date The baseline that turns wear into a rate
Installation record Date into service and position in the line
Pumping log Cubic metres conveyed, pressure range, mix description
Failure photographs with scale Where it failed: body, weld, collar or seal face
Cut section photograph Wall loss distribution and whether the hardened layer is intact
Blockage and over-pressure history Whether an excluded event occurred

The cut section is the single most useful item and the one buyers most often omit. A sectioned pipe shows whether the loss is uniform abrasive wear, which is normal, or localised gouging and cracking, which points to a material or heat treatment issue. Suppliers can read a sectioned pipe; they cannot read a description of one.

How a pro-rata claim is calculated

Most wear guarantees settle on a pro-rata credit rather than a replacement, because the pipe did deliver some service. The formula is simple enough that it should be written into the PO.

An illustration: a guarantee of 40,000 m³, actual service 26,000 m³ before failure, shortfall 14,000 m³, or 35 per cent of the guaranteed volume. On a unit price of USD 60, the credit is USD 21 per pipe. Two details decide whether that number is real: whether the credit is against cash or against the next order, and whether the return freight is deducted. On heavy steel, the return freight can exceed the credit, which is why most settlements are handled as a credit on a future shipment with no physical return.

Five reasons claims fail

  • No baseline. The buyer cannot show starting thickness, so cannot show a wear rate.
  • Mixed batches. Pipes from three heats were installed interchangeably, so the failed pipe cannot be traced to the batch that failed.
  • Wrong position. Standard pipe was used on the high-pressure riser, where the guarantee conditions did not apply.
  • End damage from handling. A dropped or re-welded end shows up in the failure mode, and falls under exclusions.
  • Late notice. The pipe was scrapped or re-purposed before the supplier could inspect it, which removes the physical evidence.

Blockage damage deserves separate mention because it is frequently misread as wear. A line that blocks and is restarted at full pressure can burst a pipe that was still within its service wall. That is a pressure event, not a wear failure, and the analysis of line blowouts explains how to distinguish the two from the failure pattern.

Seven clauses for the purchase order

None of this needs a lawyer, but it does need to be agreed before the deposit.

  • Wear guarantee stated in cubic metres, by variant and by line position
  • Reference conditions: aggregate, slump, pressure range, diameter
  • Starting wall thickness measured and recorded at both ends before shipment
  • Heat number marked on each pipe and listed on the packing list
  • Claim notice window, counted from the date the retirement thickness is reached
  • Remedy: replacement, pro-rata credit, or credit against a future order
  • Who bears inspection cost and freight in each outcome

Hongchang Machinery marks and documents production by batch and supplies material and hardness records with export orders, so a buyer can build the baseline file described above at goods-in. The published design life for each quenched pipe variant is the correct starting point for a guarantee figure, and the clamp range should be specified in the same order so the assembly is not mixed with fittings of unknown origin.

Send the pumping conditions, the position in the line and the volume you expect per year, and the reply can state the design life and documentation that apply to that duty.

Share to:
facebook
line
Whatsapp
Pinterest
Tumblr
Linkedin